Warning: Tuned e-bikes & e-scooters are not permitted within the road traffic regulations!

MTT SmartChip V2 – Tuning Chip for Bosch Smart System

Exclusively at EBikeTuningShop

MTT SmartChip V2 for Bosch Smart System

Compact chip. Installed once. Switchable without tools.

The MTT SmartChip V2 by MountainTuning is a compact tuning chip for e-bikes with the Bosch Smart System and Gen5. It is installed once inside the motor compartment and fits even where space is tight.

Version 2 comes with noticeably higher-quality connectors. Power comes from the bike – no extra battery. Three operating modes are selected with wheel movements, without an app or PC.

Developed in Germany. Available exclusively at EBikeTuningShop.com.

€159 at EBikeTuningShop.com · incl. VAT, plus shipping

MTT SmartChip V2 tuning chip for Bosch Smart System

Compatible up to and including Bosch firmware 21.12.0

Why a chip

Install once. Forget it's there.

The SmartChip is for riders who want tuning permanently installed – with nothing to attach and nothing to lose.

01

Very small

The chip is tiny and fits even in tight motor compartments where larger modules don't.

02

Better connectors (V2)

Version 2 uses noticeably higher-quality plug connections for a secure fit inside the motor.

03

Easy to remove

Unplug the chip and reconnect the sensor cable – the bike is back to its original state.

04

Three modes, no app

Tuning on, tuning off, or decide at switch-on – selected with wheel movements.

05

No battery

Powered by the e-bike itself. Nothing to charge, nothing to replace.

06

Proven in the field

Tested and used on e-bikes from CUBE, Haibike, Kalkhoff, KTM, Winora, Focus and many more.

MTT SmartChip V2 connectors in detail
How it works

Once installed, the SmartChip reads the speed signal from the sensor and – with tuning active – passes an adapted signal to the motor. The motor keeps assisting beyond the factory limit of 25 km/h.

E-mountain bike rider climbing a steep rooty trail in a dark forest
Installed once inside the motor – on the trail you just ride.
Back to top
Compatibility check

Does the SmartChip fit your Bosch e-bike?

The SmartChip V2 fits the Bosch Smart System (also called BES3 or Gen4 2022) and Bosch Smart System Gen5 (from 2024, often called CX Gen5) – if all points below apply.

Your bike needs

  • ✓Bosch Smart System or Gen5 (square charging plug)
  • ✓Classic spoke magnet with speed sensor on the rear frame
  • ✓Bosch firmware up to and including 21.12.0

Not compatible

  • ✕Bosch e-bikes with ABS
  • ✕E-bikes with a rim or valve magnet
  • ✕Older Bosch Gen2, Gen3 and Gen4 with round charging plug

Quick test: look at your charging plug

Square Bosch charging plug of the Bosch Smart System and Gen5
Square plug = Smart System / Gen5 – SmartChip fits*
Round Bosch charging plug of Gen2, Gen3 and Gen4
Round plug = Gen2 / Gen3 / Gen4 – SmartChip does not fit

* provided the bike has no ABS and no rim/valve magnet. If your Bosch e-bike has neither plug, it is either not a Bosch or an older Gen1 (Classic Line).

Bosch firmware updates

Do not install Bosch updates beyond the confirmed version (21.12.0) after installing the SmartChip. Wait until we have confirmed compatibility with newer versions.

Bosch dealers often install updates automatically during a service – mention this before every inspection.

Still unsure? The Bosch Tuning Finder checks your system in a few steps.

Back to top
Operating modes

Switch tuning on and off – without opening the motor.

Even though the chip sits permanently inside the motor, you decide when tuning is active. Choose the mode with specific wheel movements when switching the bike on – the spoke magnet is moved past the sensor.

Power icon: tuning always on Factory setting

Tuning always on

Speed limit lifted. Delivered with maximum supported speed. Real speed is displayed up to approx. 22 km/h.

Power icon: tuning always off Mode 2

Tuning always off

The e-bike behaves like stock: assistance up to 25 km/h and correct speed display.

Power icon with wheel: decide at switch-on Mode 3

Decide at switch-on

Tuning activates only if the magnet sits in front of the sensor for at least 4 seconds while you switch the bike on. Otherwise it stays off.

Magnet position in front of the speed sensor for the switch-on condition

Adjustable maximum speed

The maximum supported speed can be set individually with wheel movements. All steps are described in the included manual.

Honest note on the display

With tuning active, the Bosch display shows the real speed only up to approx. 22 km/h (depending on wheel size and model). Above that the displayed value stays at or below 25 km/h, and the odometer no longer matches the real distance. Tip: use GPS on your smartphone in a handlebar mount.

Smartphone with a map in a handlebar mount on an e-mountain bike on a forest trail
Tip: for your real speed, use GPS on a smartphone in a handlebar mount.
Back to top
Variant

SmartChip "Switch" – for bikes without a display

The Switch version has an additional function: cut one small wire and an alternative start routine for tuning becomes active. Reconnect the wire and all standard setting options are available again.

It was designed for Bosch Smart System e-bikes without a display, but works on any Bosch Smart System bike with a spoke magnet. Details are in the manual.

Which one do I need?

  • SmartChip V2: the standard choice for bikes with a Bosch display
  • SmartChip Switch: for bikes without a display, or if you want the alternative start routine
View Switch version
Back to top
Installation

Inside the motor compartment – in a few steps.

The SmartChip is plugged into the speed sensor connection inside the motor compartment. No extra power supply is needed.

Hands loosening the motor cover screws of an e-mountain bike with a Torx key in a workshop
Step 1: open the motor cover – on some bikes the crank arm comes off first.

1Open the motor cover

Remove the plastic motor cover – on some bikes a crank arm has to come off first.

2Plug in the chip

Connect the SmartChip between the speed sensor cable and the motor.

3Close the cover

Tuck the chip into the motor compartment and refit the cover and crank.

4Ride

Switch the bike on – the chip starts in "tuning always on". Change modes any time.

Tools you may need

  • Torx or Allen key for the motor cover
  • Crank puller (depending on the bike)

Not comfortable with this? Any bike workshop can do the installation.

In the box

  • 1 MTT SmartChip V2
  • Manual

Power supply: via the e-bike, no battery required.

Back to top
Choose your form

SmartChip, Splug or SmartSensor?

All three use the same signal-based MountainTuning principle for the Bosch Smart System. The difference is how they are built in.

SmartChip V2 Splug SmartSensor
Form Chip inside the motor Magnetic dongle on frame or handlebar Replacement speed sensor
Tuning on / off 3 modes via wheel movements Attach / remove dongle 3 modes via wheel movements
Installation Open motor cover, plug in Open motor cover, plug in harness, fix holder Swap the original sensor
Best for Fit and forget Tuning you can take off Keep the original sensor to swap back
Buy SmartChip V2 About Splug About SmartSensor
Back to top

Frequently asked questions

Does it work with Bosch Gen5 / CX Gen5?

Yes – the Bosch Smart System Gen5 (from 2024) is supported, provided the bike has no ABS and no rim/valve magnet.

Which Bosch firmware is supported?

Up to and including Bosch firmware 21.12.0. Please install newer Bosch versions only after we have confirmed compatibility.

Can I switch the tuning off?

Yes. Choose "tuning always off" or "decide at switch-on" with wheel movements when switching the bike on. In "always off" the bike behaves like stock with assistance up to 25 km/h.

Why does my display stop showing the real speed?

To keep the motor assisting, the chip keeps the speed value for the Bosch system at or below 25 km/h. The display therefore shows the real speed only up to approx. 22 km/h and the odometer differs from the real distance. Use GPS for your real speed.

Do I need an app, a PC or a battery?

No. Settings are made with wheel movements, and the chip is powered by the e-bike.

What is the difference between V2 and Switch?

Both are the same chip. The Switch version adds an alternative start routine that is activated by cutting a small wire – designed for bikes without a display.

Can I remove the chip later?

Yes. Open the motor cover, unplug the chip and reconnect the original sensor cable directly.

Where can I buy it and which countries are shipped to?

The SmartChip V2 is available exclusively at EBikeTuningShop.com. Orders ship to most EU countries; customers in Switzerland use a separate shipping service. Currently no shipping to France, the USA or Canada.

May I ride on public roads with the SmartChip?

Not with tuning active. Tuned e-bikes are not permitted on public roads. Please read our warnings and observe the laws of your country.

Back to top
Exclusively at EBikeTuningShop

Ready for the SmartChip V2?

Check your bike against the compatibility list, then order at EBikeTuningShop.com.